Small Jib Crane

A small jib crane provides controlled lifting within a defined workstation, without the coverage or structural scale of an overhead crane. It is intended for loads up to 1,000 kg where operators repeatedly position components at machines, assembly benches, maintenance points or packing stations.

 

 

 

Configuration	Structural arrangement	Working characteristic	Typical use
Wall-Mounted Jib Crane	Jib arm fixed to a verified wall, steel column or dedicated support bracket	Keeps the floor clear; provides local coverage along the arm radius	Machine loading, work cells, maintenance bays
Articulating Jib Crane	Two pivoting arm sections with independent slewing movement	Reaches around obstructions and positions loads within confined areas	Tool handling, assembly, repair stations
Low-Headroom Small Jib Crane	Compact arm and hoist arrangement selected for restricted vertical clearance	Retains practical hook height under low ceilings or existing services	Low-ceiling workshops, equipment rooms

A small jib crane is not defined by boom length alone. The load path, rotation envelope and attachment point must be evaluated together. A longer arm increases the overturning moment at the wall connection; therefore, capacity and reach are selected as a matched set rather than as independent values.

 

 

Small jib cranes are generally specified for light-duty lifting up to 1,000 kg. The usable capacity depends on the crane configuration, arm length, hoist weight, lifting attachment and duty cycle. The rated load must include the weight of below-hook devices when they remain attached during lifting.

Typical project inputs include:

• Rated load: up to 1,000 kg
• Working radius: confirmed from the pick point to the set-down point
• Lifting height: determined by the load height, hook approach and available headroom
• Slewing range: set to suit the work zone and avoid doors, machinery, pipework or personnel routes
• Hoist type: manual chain hoist or electric chain hoist, selected for duty and positioning requirements
• Control method: hand chain, pendant control or optional remote control where the risk assessment permits

The stated capacity applies only within the approved radius and installation arrangement. A structural review is required before finalizing the mounting method.

 

 

A wall-mounted small jib crane is installed on an existing reinforced concrete wall, steel building column or purpose-designed support structure. It does not require a floor-mounted mast, making it suitable where forklift lanes, assembly tables or material flow routes must remain unobstructed.

The jib arm rotates through a defined angle according to the mounting location and interference limits. The trolley travels along the arm while the hoist performs the vertical lift. This arrangement gives the operator direct coverage over a machine or workstation without occupying floor area beneath the crane.

Before installation, the supporting structure must be assessed for the crane reaction forces. Wall thickness alone is not a sufficient basis for approval. Connection design, anchor arrangement, reinforcement condition and local steelwork must be confirmed against the final load and outreach.

 

 

 

An articulating small jib crane uses two connected arms to create a more flexible lifting path. The first arm slews from the support point, while the outer arm pivots independently. This configuration is used where the hook must pass around a column, reach into a machine opening or serve a workstation with restricted access.

Compared with a straight-arm jib, an articulating crane provides closer load positioning in irregular work zones. Its operating area must still be planned carefully: the movement of both arms, the suspended load and the operator position require a clear and controlled envelope.

Articulating jib cranes are commonly selected for light components, fixtures, tools and maintenance parts. Final capacity is confirmed according to the combined arm length, mounting arrangement and required working range.

 

 

 

The hoist should be selected as part of the small jib crane system rather than added after the arm configuration is fixed. Hoist dimensions affect hook approach, headroom and the effective capacity carried by the jib.

Manual Chain Hoist

A manual chain hoist is suited to intermittent lifting where lift speed is not critical and electrical supply is unavailable or unnecessary. It provides a straightforward solution for controlled local handling.

Electric Chain Hoist

An electric chain hoist is used where lifting is repetitive, load handling frequency is higher or the operator must position parts within a defined production sequence. Pendant control can be arranged to support safe operation from the working area.

Trolley Arrangement

A push trolley is suitable for light, infrequent travel along the jib arm. For repeated handling or longer outreach, an electric trolley may be considered after reviewing duty requirements, power routing and load positioning accuracy.

 

 

A properly configured small jib crane is built around the limitations of the specific work area rather than a generic lifting rating.

• Clear floor access: Wall-mounted arrangements avoid a floor mast and base plate within the workstation.
• Controlled rotation: Mechanical stops or defined slewing limits can prevent the arm from entering restricted areas.
• Low-headroom planning: Compact hoist and trolley combinations can improve the available hook height where roof clearance is limited.
• Load positioning: Articulating arms improve access around equipment and fixed obstacles.
• Matched connection design: Brackets, bolts, plates and supporting steelwork are selected for the actual reaction forces of the crane.
• Serviceable components: Hoist, trolley and electrical items should remain accessible for inspection and maintenance.

 

 

Small jib cranes are used for repeated, localized handling rather than long-distance material transport. Typical applications include:

• Feeding components into CNC machines, presses or test equipment
• Positioning fixtures, dies and tooling at assembly stations
• Lifting motors, pumps, gearboxes and service parts during maintenance
• Supporting controlled handling at welding, grinding and inspection stations
• Transferring cartons, parts bins or fabricated components within a defined work cell
• Assisting with ergonomic handling of light loads that cannot be safely or consistently handled by hand

 

 

 

What is a small jib crane?

A small jib crane is a localized lifting system with a rotating arm and hoist, normally used for loads up to 1,000 kg. It serves a defined workstation, machine or maintenance area rather than an entire workshop.

How much can a small jib crane lift?

This product range is intended for lifting duties up to 1,000 kg. The approved capacity depends on arm length, mounting arrangement, hoist weight, duty cycle and the verified strength of the support structure.

Does a wall-mounted small jib crane need a concrete foundation?

A wall-mounted unit does not use a floor foundation or freestanding mast. However, it requires a verified load-bearing wall, steel column or engineered support bracket. The mounting structure must be checked before installation.

When should I choose an articulating jib crane?

Choose an articulating jib crane when a load must be guided around columns, machinery, corners or other local obstructions. The two-arm design provides more flexible access than a conventional straight jib arm.

Can a small jib crane be installed under a low ceiling?

Yes, provided the crane is designed around the available headroom. The arm profile, trolley type, hoist dimensions and required hook height must be reviewed together to avoid reducing usable lifting height.

Can a small jib crane use an electric chain hoist?

Yes. Electric chain hoists are commonly used for repetitive lifting and controlled workstation handling. The hoist weight, power supply, duty requirement and pendant position must be included in the crane design.

What must be checked before installation?

Confirm the actual lifted load, working radius, rotation path, mounting support, headroom, power supply and nearby obstructions. Installation should proceed only after the final drawing and structural connection arrangement are approved for the site.

 

 

Provide the rated load, working radius, lifting height, preferred mounting position and site photographs or drawings. A suitable small jib crane configuration can then be developed for the workstation, including the jib type, hoist arrangement, slewing range and support connection requirements.

Hot Tags: small jib crane, China small jib crane manufacturers, suppliers, factory, 1 Ton Electric Hoist, Column Mounted Jib Crane, Jib Crane By Types, Pillar Mounted Jib Crane, Wall Bracket Jib Crane, Wall Mounted Jib Crane