Workstation Jib Crane

A workstation jib crane is designed for short-range lifting tasks that occur repeatedly around a machine, workbench, test station, or production cell. KINOCRANES workstation lifting systems combine a compact slewing structure with a low-resistance trolley path, giving operators controlled access to loads without occupying the full working envelope of an overhead bridge crane.

The product is intended for industrial users worldwide. Final capacity, dimensions, hoist selection, mounting method, electrical configuration, and compliance documentation are determined from the application, site conditions, and requirements applicable in the destination country.

 

 

The value of a workstation jib crane is not limited to its rated capacity. It is the ability to place a load at the point of use with repeatable control, while keeping the operator's movement direct and the surrounding floor clear. This makes the system suitable for frequent handling cycles where a full overhead crane would be excessive or unavailable.

• Defined coverage: The jib serves a controlled working radius, reducing unnecessary travel between the pickup point and the point of use.
• Low-effort positioning: Manual slewing and trolley travel can be configured for smooth movement, helping reduce the physical effort associated with repeated handling.
• Adaptable installation: Floor-mounted, wall-mounted, column-mounted, and portable-base arrangements can be matched to the building structure and workcell layout.
• Tool integration: The lifting interface can be configured for electric chain hoists, manual hoists, air balancers, vacuum lifters, or other approved below-the-hook devices.

 

 

Workstation jib cranes can be supplied with an enclosed track or a conventional I-beam arm, depending on the load profile, reach, operating frequency, and preferred handling method.

Enclosed track workstation jib crane

An enclosed track protects the trolley running surfaces from common workshop contaminants such as dust, chips, and production debris. Its lower moving mass and guided trolley arrangement are well suited to high-cycle manual handling, ergonomic tool support, and accurate load positioning.

I-beam workstation jib crane

An I-beam arm provides a familiar structural arrangement for applications requiring a robust steel boom, a broader range of trolley options, or a transition from existing jib crane equipment. Selection should account for hoist and trolley weight, impact conditions, duty cycle, and available headroom.

 

 

Floor-mounted workstation jib crane

A free-standing or pillar-mounted design provides a dedicated lifting point within an open production area. Depending on the model and supporting slab, the unit may be anchored to a verified existing concrete floor or require a purpose-designed foundation. Structural verification is required before installation.

Wall-mounted or column-mounted workstation jib crane

A wall- or column-mounted jib uses an existing structural support and preserves floor area below the crane. This arrangement is useful beside fixed equipment and along narrow work aisles, provided the supporting structure can withstand the imposed vertical forces, horizontal forces, and moments.

Portable-base workstation jib crane

Where workstations change frequently, a portable-base configuration can provide relocation flexibility. The base, lifting capacity, travel method, and operating procedure must be selected for the intended floor condition and handling environment; portability does not remove the need for a stability assessment.

 

 

The following values are indicative configuration ranges for preliminary product evaluation and project discussion. Actual parameters are engineered according to the load characteristics, working radius, support structure, duty class, lifting height, and destination-country requirements.

Technical item	Indicative range / description
Rated capacity	Approximately 50–2,000 kg; the applicable limit depends on arm design, span, duty class, and mounting arrangement
Working radius / arm length	Approximately 2–6 m is common; the reach can be configured for the required work envelope
Slewing range	Up to 360° for selected floor- or pillar-mounted designs; wall- and column-mounted versions are configured around the supporting structure and may include slewing limits
Lifting height	Determined by building clearance, equipment height, hook approach, and the required load path; no single fixed value applies to every installation
Arm type	Enclosed track or I-beam; selected according to capacity, handling frequency, positioning requirements, and maintenance environment
Mounting options	Floor-mounted, wall-mounted, building-column-mounted, or portable-base configurations
Hoist and lifting device options	Electric chain hoist, manual chain hoist, air balancer, vacuum lifter, and other compatible below-the-hook equipment
Control options	Manual operation, pendant control, or radio remote control, subject to hoist type, handling frequency, and safety requirements
Operating environment	Indoor or specified outdoor use; dust, humidity, temperature, and corrosive exposure must be confirmed during design
Technical documentation	Layout drawings, foundation or support reactions, equipment data, and destination-market documentation can be prepared as required by the project

Note: The values above are preliminary reference ranges and do not replace final design data or the rated-load marking on the completed crane. For loads above 1,000 kg, extended arms, high-cycle duty, or special environments, complete load and site information should be reviewed before quotation.

 

 

A workstation jib crane is most effective when the lifting point is close to the process and the same handling motion is repeated throughout the shift. The following applications illustrate where a compact jib can solve a specific access or positioning problem.

• Die and mould changeover: Position stamping dies, injection moulds, trim tools, and associated fixtures during changeover, inspection, and storage preparation. The controlled radius helps keep the load close to the machine interface without requiring a large crane runway.
• Battery enclosure and module handling: Support the controlled placement of battery housings, modules, covers, and service tooling during pack preparation or test work. A suitable lifting attachment and a verified load path are required for sensitive or uneven loads.
• Pump, motor, and coupling alignment: Hold rotating equipment and drive components at a stable working height while technicians align shafts, inspect couplings, or position components on a skid. Fine manual movement can be more useful than a long-travel overhead system in this type of task.
• Roll and core handling in converting operations: Move paper cores, film rolls, mandrels, and tooling between a preparation stand and the process interface when the load needs a short, repeatable arc rather than a long horizontal transfer.
• Test bench and inspection equipment access: Place instruments, enclosures, test fixtures, or heavy assemblies onto a test stand and remove them after verification. The crane can be arranged around the bench without occupying the entire test area.
• Foundry and metal-finishing support: Handle mould boxes, ladle accessories, grinding fixtures, and finishing tools at a defined station where heat, dust, or debris requires appropriate component protection and a documented operating procedure.

 

 

Q: What is a workstation jib crane used for?

A: It is used for repetitive, localized lifting around a machine, workbench, test station, or production cell. The jib provides a defined working radius so loads can be moved between nearby positions without deploying a full overhead crane system.

Q: What is the difference between a workstation jib crane and a standard jib crane?

A: A workstation jib crane is generally selected around operator access, frequent handling, compact coverage, and integration with a workcell. A standard industrial jib may be selected primarily for heavier loads, longer reach, or more demanding structural duty. The correct choice depends on the load and duty cycle rather than the product name alone.

Q: Is an enclosed track always better than an I-beam?

A: No. Enclosed track is often advantageous for smooth manual movement and contaminated workshop environments, while an I-beam may be preferred for a particular span, load range, trolley arrangement, or existing crane layout. Selection should be based on the complete application.

Q: Does a floor-mounted workstation jib crane need a special foundation?

A: Not always. Some configurations can be anchored to a verified existing concrete slab, while others require a dedicated foundation. The decision depends on capacity, reach, overturning moment, anchor design, and the actual condition of the supporting floor.

Q: Can a workstation jib crane be mounted to a building column?

A: It can be, provided the column and its connections are verified for the vertical and horizontal reactions introduced by the crane. A building column should not be treated as a suitable mounting point without structural review.

Q: Which hoist can be used with a workstation jib crane?

A: Common choices include electric chain hoists, manual chain hoists, air balancers, and vacuum lifting devices. The hoist must match the rated capacity, lift height, duty class, control method, and environmental conditions of the crane.

Q: What information is required for a workstation jib crane quotation?

A: The basic information includes rated load, load dimensions, required reach, lifting height, operating frequency, mounting preference, available headroom, floor or building support details, power supply, operating environment, and destination-country compliance requirements.

Q: How should a workstation jib crane be maintained?

A: Maintenance should follow the supplier's instructions and the rules applicable at the installation site. Routine attention normally includes checking anchors and fasteners, inspecting the arm and trolley, testing controls and limit devices, monitoring the hoist and lifting attachment, and recording required inspections.

Hot Tags: workstation jib crane, China workstation jib crane manufacturers, suppliers, factory, 1 Ton Electric Hoist, Column Mounted Jib Crane, Jib Crane By Types, Pillar Mounted Jib Crane, Wall Bracket Jib Crane, Wall Mounted Jib Crane